California Instruments 801RP Series Spécifications télécharger pdf (Page 117)

To measure the RMS current, use:

MEAS:CURR?

To measure the peak current, use:

MEAS:CURR:AMPL:RES /* resets track and hold for peak curr. meas.

/* It may be need to turn the output on or program

/* as specific voltage at this time before taking a

/* peak current reading.

MEAS:CURR:AMPL:MAX? /* retrieves peak current reading.

To measure the current crest factor, use:

MEAS:CURR:CRES?

Power Measurements

To measure the true power, use:

MEAS:POW:REAL?

To measure the apparent power, use:

MEAS:POW:APP?

To measure the power factor, use:

MEAS:POW:PFAC?

1 2 ... 112 113 114 115 116 117 118 119 120 121 122 ... 125 126

Model 2003RP 1
AC Power Source 1
User and Programming 1
SAFETY SYMBOLS 5
1 Introduction 11
2 Specifications 12
2.2 Supplemental 15
2.3 Measurements [Option] 16
2.4 System Specification 17
2.5 Unit Protection 18
2.6 Mechanical 18
2.7 Environmental 19
2.8 Regulatory 19
2.9 Front Panel Controls 20
2.10 Available Options 21
3.1 Unpacking 22
3.2 Power Requirements 22
3.2.1 AC Line Voltage 23
3.2.3 Input Power 23
3.4 Mechanical Installation 27
3.5 Input Wiring 27
3.6 Output Connections 28
3.7 Output Voltage Ranges 30
3.8 Functional Test 31
4 Front Panel Operation 33
4.1.2 Control knobs 36
4.1.3 Buttons 36
4.1.4 LED Displays 37
4.2 How to examples 38
4.2.1 Set the Output 38
4.2.2 Slew Output Values 38
4.2.5 Control the Output 40
4.4 Current Limit Modes 42
4.6 Remote Inhibit [Option] 43
5 Principle of Operation 44
5.4 Mother Board 47
5.5 Amplifier Modules 47
5.6 Oscillator Module 47
5.7 Range/Relay Board 47
5.8 Output Board 48
CAUTION 49
6 Calibration 50
6.3 Routine Calibration 52
6.4 Non-Routine Calibration 56
6.4.3 Open Sense Adjustment 59
7 Service 60
Table 7-4: Distorted Output 61
7.4 Module Removal 63
7.5 Replaceable Parts 66
Table 7-9: Fuses 67
8 Remote Control 68
Figure 8-1: Rear Panel View 69
8.3 IEEE Interface 70
8.4 RS232C Interface 71
8.4.2 Serial Cable Diagram 73
Symptoms: 75
Things to check first: 75
Resolution for Symptom 1 75
Procedure 76
Resolution for Symptom 2 77
8.9 Software Registration 81
9 Introduction to SCPI 82
9.3 Using Queries 84
9.5 SCPI Data Formats 87
10 SCPI Command Reference 88
10.2 Calibration Subsystem 89
10.2.1 Calibration State 89
10.2.3 Output Calibration 92
10.3 Measurement Subsystem 93
10.4 Instrument Subsystem 96
10.5 Source Subsystem 97
10.6 Output Subsystem 100
10.7 Limit Subsystem 104
10.8 Display Subsystem 105
10.9 System Commands 106
10.10 Common Commands 108
10.10.2 *ESE 109
10.10.1 *CLS 109
10.10.3 *ESR? 110
10.10.4 *IDN? 111
10.10.5 *RCL 111
10.10.6 *RST 112
10.10.7 *SAV 113
10.10.8 *SRE 113
10.10.9 *STB? 113
11 Programming Examples 114
11.3 Making Measurements 116
12 Status Registers 118
12.3 Status Byte Register 119
12.4 Examples 120
Command Syntax Tree 121
Appendix C: Error Messages 123

Commentaires sur ces manuels

Pas de commentaire

California Instruments 801RP Series Spécifications Page 117

Commentaires sur ces manuels

Produits connexes et manuels pour Mesure, test et contrôle California Instruments 801RP Series