California Instruments 801RP Series Spécifications Page 49
- Page / 126
- Table des matières
- MARQUE LIVRES
- Model 2003RP 1
- AC Power Source 1
- User and Programming 1
- SAFETY SYMBOLS 5
- 1 Introduction 11
- 2 Specifications 12
- 2.2 Supplemental 15
- 2.3 Measurements [Option] 16
- 2.4 System Specification 17
- 2.5 Unit Protection 18
- 2.6 Mechanical 18
- 2.7 Environmental 19
- 2.8 Regulatory 19
- 2.9 Front Panel Controls 20
- 2.10 Available Options 21
- 3.1 Unpacking 22
- 3.2 Power Requirements 22
- 3.2.1 AC Line Voltage 23
- 3.2.3 Input Power 23
- 3.4 Mechanical Installation 27
- 3.5 Input Wiring 27
- 3.6 Output Connections 28
- 3.7 Output Voltage Ranges 30
- 3.8 Functional Test 31
- 4 Front Panel Operation 33
- 4.1.2 Control knobs 36
- 4.1.3 Buttons 36
- 4.1.4 LED Displays 37
- 4.2 How to examples 38
- 4.2.1 Set the Output 38
- 4.2.2 Slew Output Values 38
- 4.2.5 Control the Output 40
- 4.4 Current Limit Modes 42
- 4.6 Remote Inhibit [Option] 43
- 5 Principle of Operation 44
- 5.4 Mother Board 47
- 5.5 Amplifier Modules 47
- 5.6 Oscillator Module 47
- 5.7 Range/Relay Board 47
- 5.8 Output Board 48
- CAUTION 49
- 6 Calibration 50
- 6.3 Routine Calibration 52
- 6.4 Non-Routine Calibration 56
- 6.4.3 Open Sense Adjustment 59
- 7 Service 60
- Table 7-4: Distorted Output 61
- 7.4 Module Removal 63
- 7.5 Replaceable Parts 66
- Table 7-9: Fuses 67
- 8 Remote Control 68
- Figure 8-1: Rear Panel View 69
- 8.3 IEEE Interface 70
- 8.4 RS232C Interface 71
- 8.4.2 Serial Cable Diagram 73
- Symptoms: 75
- Things to check first: 75
- Resolution for Symptom 1 75
- Procedure 76
- Resolution for Symptom 2 77
- 8.9 Software Registration 81
- 9 Introduction to SCPI 82
- 9.3 Using Queries 84
- 9.5 SCPI Data Formats 87
- 10 SCPI Command Reference 88
- 10.2 Calibration Subsystem 89
- 10.2.1 Calibration State 89
- 10.2.3 Output Calibration 92
- 10.3 Measurement Subsystem 93
- 10.4 Instrument Subsystem 96
- 10.5 Source Subsystem 97
- 10.6 Output Subsystem 100
- 10.7 Limit Subsystem 104
- 10.8 Display Subsystem 105
- 10.9 System Commands 106
- 10.10 Common Commands 108
- 10.10.2 *ESE 109
- 10.10.1 *CLS 109
- 10.10.3 *ESR? 110
- 10.10.4 *IDN? 111
- 10.10.5 *RCL 111
- 10.10.6 *RST 112
- 10.10.7 *SAV 113
- 10.10.8 *SRE 113
- 10.10.9 *STB? 113
- 11 Programming Examples 114
- 11.3 Making Measurements 116
- 12 Status Registers 118
- 12.3 Status Byte Register 119
- 12.4 Examples 120
- Command Syntax Tree 121
- Appendix C: Error Messages 123
Produits connexes et manuels pour Mesure, test et contrôle California Instruments 801RP Series
(223 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.150 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels